In order to meet the area of industrial control equipment, high-performance, high integration and to improve maintenance performance requirements, Omron (OMRON) is about to launch a new highly scalable based small-scale Yi Tihua programmable???ì??????§(PLC) - SYSMAC CP1H, mainly CP1H-X (Standard), CP1H-XA (analog built-in type) and CP1H-Y (high-speed positioning type) that three kinds of models. CP1H set CS / CJ various functions into one, through a variety of features built-enriched, enhanced application capabilities, and shorten the complicated process of additional design time. Have followed many of the new features, this new small PLC can be applied to textiles, packaging, food, printing, and some need-driven features, such as a variety of industrial control cables and other occasions, is the similar products in the less some.
<FONT face = Verdana> CP1H located in the small machine, but it is based on the CS / CJ (in particular, CJ, CJ is a medium-sized PLC platform) platform, so a lot of medium-sized machine with features such as pulse output and analog output, etc. . Omron PLC launched before the traditional sense, mainly high-end and low-end products, but such as SYSMAC CP1H integrates several medium-sized machine features a small PLC is small, therefore, CP1H the introduction of a very important significance , which make up the product chain Omron important part of making the entire PLC Omron product chain is more fragmented.
CP1H extend a variety of I / O features such as integrated high-speed pulse output function, can be equipped with standard 4-axis; counter functionality standard with a 4-axis phase difference method; with Universal USB1.1 standard parallel port can also be equipped to achieve; more important thing, CP1H with a serial communication function, which has two main ports to achieve, you can choose the RS-232C and RS-485. In addition, the current analog monitor, which is suitable for a variety of devices plane inspection, component production in the small errors (such as screw looseness) to prevent tools, and molding machine s hydraulic control and other occasions. These I / O functionality allows the user specific application needs and cost constraints to choose, and can extend a variety of other applications, such as Ethernet, which fully reflects the SYSMAC CP1H high degree of flexibility. CP1H support standardDeviceNet fieldbus, can also correspond to Ethernet, CLK-peer networks.
CP1H the availability of standard with a 4-axis high-speed pulse output function Zaigaojingdu Dingweifangmian can Fahui advantages, particularly for electronic product manufacturing equipment electrolytic capacitor of the assembly, Yijibaozhuang machine s feed and other applications occasions. CP1H-X series can achieve 100kHz972 30kHz972 shaft axis and high-speed pulse output; CP1H-Y is a linear drive built 1MHz input / output, and also with 20 points (12 input, 8 output) General input / output, to achieve 100kHz972 axis and 30kHz972 axis pulse output.
CP1H high-speed counter function make it particularly suitable for applications in fiber equipment, textile machinery, spindle control, and building materials manufacturing machinery, stone cutting machine handling positioning occasions. Shaft axis and 10kHz978 largest 100kHz974 a total of 12 axis counter, built-in 8-point input interrupt function, and pulse width with 50BCs capture capabilities. These properties make CP1H CPM2A with Omron introduced earlier than the basic instructions increased by 6 times, while the MOV instruction is increased 26 times. Not only is the basic instructions, application instructions also achieved high speed, these are high-speed for the device as a whole has helped.
CP1H equipped with a standard USB1.1 port and two serial communication interface (RS-232C and RS-485), in connection PT, various components (inverter, temperature control and smart sensors, etc.), as well as between PLC serial connection, while also easy to achieve with your computer. If more than one boiler control, the need to set and monitor a variety of devices, then, CP1H up to 9 units can be achieved between the 10 channels within the data exchange. But the serial PLC link function only CP1H two serial ports one of the entry into force.
CP1H the CPU is based on the CJ platform, although located in the small machine applications, but the speed and processing capabilities have been much higher than the minicomputers of the areas, so more general minicomputer has obvious performance advantages, a basic instruction in handling the the time required only 0.1BCs, the general handling of small PLC CPU, the same instruction time required over the 0.6BCs. Users can select the application requirements and cost constraints of different grades (CP1H-X, CP1H-XA and CP1H-Y) of the CPU,
CP1H possess other features include:
???? Memory Box: Can your program and the initial value data to copy to other devices ???? 7 segment LED low-battery status display ???? Operation: When powered on, CPU built-in flash memory can be saved and output to all DM area (32Kw) The initial value of up to 20k step program ???? ???? capacity points up to 320 I / O
???? 37 analog in software, CP1H additional complicated procedures to shorten the design time. The use of the CJ of the programming environment to support FB-ST s programming. Includes a variety of function blocks. When users need to connect to another when a smart Kongzhi system, without many procedure to configure Gezhongcenshuo, just Jiang s Gongneng corresponding block of program library Zhong transfer Chu, or automatically to achieve the corresponding functions.
Programming environment optimized use of structured text (ST) language, to make numerical computation easier; communication program from the Smart FB, can be achieved for a variety of communications ladder program, which will substantially reduce application development and debugging time. In addition to other PLC, both high-functioning unit parameter settings or a variety of FA network configuration, through the use of simple programming software CX-Programmer, a variety of applications pre-standard Qiehuan block (ladder / ST language), are without access to manuals, you can easily set directly.
CX-One is for the Omron PLC components, including the connection, setting and programming of the FA kit, CP1H only by CX-Programmer to program, set. CX-One contains the NS series programmable terminal, temperature controller, the programming / configuration tools package, and CP1H